Product Description - QUIKCOPPER® is a hand-mixable, copper-reinforced, epoxy putty that mixes in just one minute to provide fast repairs to pipes, tanks, and vessels made of copper, brass, bronze, and other non-ferrous metals. It comes in a handy four-ounce "tootsie roll" form with the curing agent encapsulated in the contrasting color base material. The putty-like consistency eliminates drips and runs, providing "no mess" applications with no tools required for use.

This "Plumber in a Tube" can save homeowners and businesses hundreds of dollars annually on repairs.

Basic Uses - After proper mixing, QUIKCOPPER® molds like clay to fill in and surround leaks in the most intricate of openings and breaks in pipes, elbows, joints, sleeves, sink traps, drains, water heaters, water tanks, etc. It is ideal for sealing freeze breaks and pin hole leaks and will seal high pressure hot water lines. QUIKCOPPER® bonds to damp, wet, and slowly leaking surfaces. It contains no solvents, does not shrink upon curing, and is non-toxic. After finally curing, it can drilled, filed, tapped, sanded, painted and machined. The unused portion of QUIKCOPPER® will remain stable for years if stored in its container at room temperature.

Color - Simulated copper color after cure.

Packaging - QUIKCOPPER® is packed in a reusable clear plastic tube with a plastic friction top.

Applicable Standards - Certified by the National Sanitation Foundation (NSF INTERNATIONAL) for use in contact with potable water under Standard 61 – Drinking Water System Components – Health Effects. Authorized by USDA for use in federally inspected meat and poultry plants.

Surface Preparation:
In order to achieve optimum adhesion, surfaces should be clean and free of grease and dirt. Scuffing or sanding the surface prior to cleaning helps ensure a good bond.
Mixing:
Twist or cut off required amount. To mix, knead with fingers to a uniform color. If mixing is difficult, warm QUIKCOPPER® to a room temperature of slightly above. Apply to the surface to be repaired (within two minutes of mixing). Force into any cracks or holes to be filled and strike off excess material, preferably with a tool wetted with clean water. When applying to a damp, wet, or slowly leaking area, work he material forcefully into the surface and apply pressure until adhesion begins to take effect.
For a smooth appearance of the cured compound, hand rub with water or a damp cloth prior to hardening. Remove excess material before hardening begins. After 5-10 minutes the epoxy will begin to form a tenacious bond. After just 60 minutes QUIKCOPPER® can be drilled, sawed, carved, sanded, stained, or painted.

Health Precautions - When mixing by hand, QUIKCOPPER® does not cause skin irritation to individuals with normal skin sensitivity. Individuals with extra sensitive skin should maintain caution and wash hands thoroughly after mixing the compound, or wear thin plastic gloves. QUIKCOPPER® has been classified non-toxic and non-skin irritating when tested versus the requirements of the Federal Hazardous Substances Labeling Act.

1. May cause irritation to sensitive skin. Wash hands with soap and water after use.
2. Eye irritant. In case of eye contact, flush with water. Contact physician.
3. May be harmful if swallowed.
4. Keep out of reach of children.
5. Not intended for use in structural applications.
6. When sanding cured putty or substrate, use protective eye wear and dust mask.

Warranty - All recommendations, statements and technical data contained herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed of implied. User shall rely on his own information and tests to determine suitability of the product for intended use, and user assumes all risk and liability resulting from the use of this product.
Manufacturer’s sole responsibility shall be to replace that portion of the product of the manufacturer which proves to be defective. Manufacturer shall not be liable to the buyer or any third party for injury, loss or damage directly or indirectly resulting from use of, or inability to use the product.
Recommendations or statements other than those contained in a written agreement signed by an officer of the manufacturer shall not be binding upon the manufacturer.